Stencil Orders and Instructions

 

ORDER At Bottom Of PAGE

Step By Step Instructions Are Included In All Kits.

Still skeptical about your painting skills.... Review the instructions below, then order the kit you need!

 

GENERAL INSTRUCTIONS

 Reelfoot Grass™ and Grass Lands

 STEP1: SHADOWING TECHNIQUE (Flat Black)

Using the flat black paint, lightly apply large and small randomly shaped patches every few feet.  These areas should range in size from 3 – 4 inches in width to 1-2 feet in height.  Be careful not to apply the paint too heavily as patches are simulating shadows.

STEP 2: BARK PATTERN APPLICATION (Flat Dark Brown)

Place the stencil over the area you wish to begin.

The top corners of the stencil will be taped to the surface using electrical or masking tape.  The electrical tape will allow easy removal and can be reapplied several times.  

The stencil should be applied length wise so the break-up pattern is vertical in appearance.  The edges of the stencil should over-lap each time so that the pattern seems to be continuous.

While applying the paint do not sweep the gun.  Keep the gun perpendicular to the stencil this will reduce over spray and keep the pattern sharp.

STEP 3: ORIGINAL GRASS PATTERN APPLICATION (Khaki or Desired Color)

Note: New Reelfoot Grass Stencils can be randomly rotated as they are placed to get the desired effect.

Using the grass stencil as you did with the bark pattern, attach the stencil to the surface using electrical or masking tape at the corners.  Apply the pattern using Khaki paint or whatever color you desire for the grass.  For additional depth in the grass randomly spray areas of the stencil lightly with a medium brown.  This is done before moving the stencil to the next location. To obtain a bush effect continue to paint over the same area moving your stencil 1 to 2 inches each time in between paint application.  A few seconds to a few minutes may be needed before re-applying the stencil over a freshly painted area.

               

Reelfoot Thicket™

1.       Apply the break-up pattern as described in the general instructions (including the shadowing technique).

2.       Place the thicket pattern at the desired angle on the equipment using tape and apply Dark Brown paint.

3.       Before moving the stencil shadow the twigs with a light dusting of medium brown on the pattern for desired highlights.

Leaves

Place the leaf pattern where desired using electrical tape to hold the stencil in placeIt is extremely important that the stencil not move once you start the following paint sequence:

1.       Base coat all the leaves on the stencil with the flat Khaki paint.

2.       Using a flat Medium Brown quickly spray the center of each leaf on the stencil with a single pass to create an over spray effect.

3.       Using the flat Dark Brown quickly spray the center of each leaf on the stencil with a single pass to create an over spray effect.  This pass will be closer and tighter than the first pass of medium brown.

4.       Lift the stencil and the leaves should have a three dimensional look as pictured below.

THE FINISHED PRODUCT

Congratulations! You have just applied the River Bottoms© Camo pattern to your favorite hunting equipment.  The camouflage should appear similar to the pictures in these instructions.  Additional photos can be found at www.reelfootcustomcamo.com.

v      Remember to always paint in a well ventilated area and follow all paint manufacturers instructions.

Note:  These instructions serve as a basic guideline from which to begin the application of our camouflage patterns to you favorite hunting equipment.  Reelfoot Custom Camo Co. implies no warranties or guaranties as to the application of our patterns, nor any liability as to the method of application or materials used.

© 1998 Reelfoot Custom Camo, Co.                                                                     www.reelfootcustomcamo.com

Revised 07/2003

 

Camoland Stencil  

STEP1: BASE COAT (Khaki or OD Green) and SHADOWING TECHNIQUE (Flat Black)

 Base coat the item using Khaki or OD Green. Using the flat black paint, lightly apply large and small randomly shaped patches every few feet.  These areas should range in size from 3 – 4 inches in width to 1-2 feet in height.  Be careful not to apply the paint too heavily as patches are simulating shadows.               

Place the stencil where desired using electrical tape to hold the stencil in placeIt is extremely important that the stencil not move once you start the following paint sequence:

 1.     Base coat the stencil with the flat Khaki paint.

2.     Using a flat Medium Brown quickly spray the center of each pattern on the stencil with a single pass to create an over spray effect.

3.     Using the flat Dark Brown quickly spray the center of each pattern on the stencil with a single pass to create a heavy over spray effect.  This pass will be closer and tighter than the first pass of medium brown.

4.     Lift the stencil and the leaves should have a three dimensional look as pictured below.

THE FINISHED PRODUCT

Congratulations! You have just applied the Camoland ™ Camo pattern to your favorite hunting equipment.  The camouflage should appear similar to the pictures in these instructions.  Additional photos can be found at www.reelfootcustomcamo.com.

 

bullet

Remember to always paint in a well ventilated area and follow all paint manufacturers instructions.

 

Note:  These instructions serve as a basic guideline from which to begin the application of our camouflage patterns to you favorite hunting equipment.  Reelfoot Custom Camo Co. implies no warranties or guaranties as to the application of our patterns, nor any liability as to the method of application or materials used.

 

© 2006 Reelfoot Custom Camo, Co.                                                                     www.reelfootcustomcamo.com

 

**ALL KITS SHIPPED USPS PRIORITY MAIL!

 - ORDER HERE -

Original Reelfoot Grass

Reelfoot Camo Corn

 

Reelfoot Thicket

Reelfoot Fall

River Bottoms®

CamoLand & CL2™

Done with or without Bark stencil to get CamoLand or CamoLand CL2

Reelfoot Grass Lands™

Camoland

Mossy Oak ® Shadow Grass

Mossy Oak ® Break Up

NatGear ™

 *Kits are not sold or shipped to Tennessee at this time. All Tennessee orders will be refunded.

    International Customers Please go to Mack's Prairie Wings Link at bottom of page!

 Small Reelfoot Stencil Kits (12" x 20") -  $25.99 (PAINT NOT INCLUDED)
bullet

Original Reelfoot Grass™ (Original Grass & Bark)

bullet

Reelfoot Thicket™ (Leaves & Twigs)

bullet

Reelfoot Fall™ (Leaves & Bark)

bullet

Camoland (Camoland & Bark)

 
Small Stencil Kit

  If Paypal will not register your order, please make sure you clear your cookies in your history.  

*Kits are not sold or shipped to Tennessee at this time. All Tennessee orders will be refunded

Large Reelfoot Stencil Kits   $39.99 (PAINT NOT INCLUDED)
bullet

Reelfoot Grass Lands™  24" x 30" -(Grass Lands & Bark)

bullet

River Bottoms® 24" x 30" -( Leaves, Bark & Twigs) *Note*Same Kit For SpringLeaves are Painted Green

bullet

NatGear 24"-26" x 24" ( Bark, Spots, Lizard Logo)

 

 

Large Name Brand Stencil Kits   $49.99 - $69.99 (PAINT NOT INCLUDED)
bullet

Mossy Oak® Shadow Grass Stencils from 15"x30" up to 20.5"x36"(Grass Lands & Bark)

bullet

Mossy Oak® Break-U® Stencils range in size from 14"x15" up to 22.5"x28.5" (Spots, Leaves, Bark & Branches)

bullet

Realtree®Max 4" 20"x36"( Grass, Limbs, Leaves) Order MAX 4  from MACK'S PRAIRIE WINGS Link below!

 

Large Stencil Kit

If Paypal will not register your order, please make sure you clear your cookies in your history.

 

Stencil Kits can also be purchased from:

Reelfoot Stencil Kits are not available in Tennessee. Tennessee Residents please go to Mack's Prairie Wings

 

Home Page